The amount of heat generated by an integrated circuit (e.g., a CPU or GPU), the prime cause of heat build up in modern computers, is a function of the efficiency of its design, the technology used in its construction and the frequency and voltage at which it operates.
The dust on the laptop CPU heat sink after three years of use has made the laptop unusable due to frequent thermal shutdowns.
In operation, the temperature levels of a computer's components will rise until the temperature gradient between the computer parts and their surroundings is such that the rate at which heat is lost to the surroundings is equal to the rate at which heat is being produced by the electronic component, and thus the temperature of the component reaches equilibrium.
For reliable operation, the equilibrium temperature must be sufficiently low for the structure of the computer's circuits to survive.
Additionally, the normal operation of cooling methods can be hindered by other causes, such as:
Dust acting as a thermal insulator red sox jersey and impeding airflow, thereby reducing heat sink and fan performance.
red sox jersey />
Poor airflow including turbulence due to friction against impeding components, or improper orientation of fans, can reduce the amount of air flowing through a case and even create localised whirlpools of hot air in the case.
Poor heat transfer due to a lack or poor application of thermal compounds.
Damage prevention
It is common practice to include thermal sensors in the design of certain computer parts, e.g. CPUs and GPUs, along with internal logic that shuts down the computer if reasonable bounds are exceeded. It is, however, unwise to rely on such preventative measures, as it is not universally implemented, and may not prevent repeated incidents from permanently damaging the integrated circuit.
The design of an integrated circuit may also incorporate features to shut down parts of the circuit when it is idling, or to scale back the clock speed under low workloads or high temperatures, with the goal of reducing both power use and heat generation.
System cooling
Fan from Papst for racks.
Air cooling
Further information: Computer fan
While any method used to move air around or to computer enclosures would count as air cooling, fans are by far the most commonly used implement for accomplishing that task. The term computer fan usually refers to fans attached to computer enclosures, but may also be intended to signify any other computer fan, such as a CPU fan, GPU fan, a chipset fan, PSU fan, HDD fan, or PCI slot fans. Common fan sizes include 40, 60, 80, 92, 120, and 140?mm. Recently, 200mm fans have begun to creep into the performance market, as well as even larger sizes such as 230 and 240mm.
In desktops
Typical airflow through a desktop ATX case.
Desktop computers typically use one or more fans for heat management. Almost all desktop power supplies have at least one fan to exhaust air from the case. Most manufacturers recommend bringing cool, fresh air in at the bottom front of the case, and exhausting warm air from the top rear.
If there is more air being forced into the system than being pumped out (due to an imbalance in the number of fans), this is referred to as a "positive" airflow, as the pressure inside the unit would be higher than outside. A balanced or neutral airflow is the most efficient[citation needed], although a slightly positive airflow results in less dust build up if dust filters are used. Negative pressure inside the case can create problems such as clogged optical drives due to sucking in air (and dust).
In high density computing
Data centers typically contain many racks of flat 1U servers. Air is drawn in at the front of the rack and exhausted at the rear. Because data centers typically contain such large numbers of computers and other power-consuming devices, they risk overheating of the various components if no additional measures are taken. Thus, extensive HVAC systems are used. Often a raised floor is used so the area under the floor may be used as a large plenum for cooled air and power cabling.
Another way of accommodating large numbers of systems in a small space are blade chassis. In contrast to the horizontal orientation of flat servers, blade chassis are often oriented vertically. This vertical orientation facilitates convection. When the air is heated by the hot components, it tends to flow to the top on its own, creating a natural air flow along the boards. This stack effect can help to achieve the desired air flow and cooling. Some manufacturers expressly take advantage of this effect.
In laptop computing
Most laptops use air cooling in order to keep the CPU and other components within their operating temperature range. Because the air is fan forced through a small port, it can clog the fan and heatsinks with dust or be obstructed by objects placed near the port. This can cause overheating, and can be a cause of component failure in laptops. The severity of this problem varies with laptop design, its use and power dissipation. With recent reductions in CPU power dissipation, this problem can be anticipated to reduce in severity.
Liquid submersion cooling
An uncommon practice is to submerse the computer's components in a thermally conductive liquid. Personal computers that are cooled in this manner do not generally require any fans or pumps, and may be cooled exclusively by passive heat exchange between the computer's parts,
The liquid used must have sufficiently low electrical conductivity in order for it not to interfere with the normal operation of the computer's components. If the liquid is somewhat electrically conductive, it may be necessary to insulate certain parts of components susceptible to electromagnetic interference, such as the CPU. For these reasons, it is preferred that the liquid be dielectric.
Liquids commonly used in this manner include various liquids invented and manufactured for this purpose by 3M, such as Fluorinert. Various oils, including but not limited to cooking, motor and silicone oils have all been successfully used for cooling personal computers.
Evaporation can pose a problem, and the liquid may require either to be regularly refilled or sealed inside the computer's enclosure. Liquid may also slowly seep into and damage components, particularly capacitors, causing an initially functional computer to fail after hours or days immersed.
Waste heat reduction
Where full-power, full-featured modern computers are not required, some companies opt to use less powerful computers or computers with fewer features. For example: in an office setting, the IT department may choose a thin client or a diskless workstation thus cutting out the heat-laden components such as hard drives and optical disks. These devices are also often powered with direct current from an external power supply brick which still wastes heat, but not inside the computer itself.
The components used can greatly affect the power consumption and hence waste heat. A VIA EPIA motherboard with CPU typically generates approximately 25?watts of heat whereas a Pentium 4 motherboard typically generates around 140?watts. While the former has considerably less computing power, both types are adequate and responsive for tasks such as word processing and spreadsheets. Choosing a LCD monitor rather than a CRT can also reduce power consumption and excess room heat, as well as the added benefit of increasing available physical desk space.
Conductive and radiative cooling
Some laptop components, such as hard drives and optical drives, are commonly cooled by having them make contact with the computer's frame, increasing the surface area which can radiate and otherwise exchange heat.
Spot cooling
In addition to system cooling, various individual components usually have their own cooling systems in place. Components which are individually cooled include, but are not limited to, the CPU, GPU and the Northbridge chip. Some cooling solutions employ one or more methods of cooling, and may also utilize logic and/or temperature sensors in order to vary the power used in active cooling components.
Passive heat sink cooling
Passive heatsink fitted on a Intel GMA graphics chip
Passive heat sink cooling involves attaching a block of machined or extruded metal to the part that needs cooling. A thermal adhesive may be used, or more commonly for a personal computer CPU, a clamp is used to affix the heat sink right over the chip, with a thermal grease or pad spread between. This block usually has fins and ridges to increase its surface area. The heat conductivity of metal is much better than that of air, and its ability to radiate heat is better than that of the component part it is protecting (usually an integrated circuit or CPU). Until recently, fan cooled aluminium heat sinks were the norm for desktop computers. Today many heat sinks feature copper base-plates or are entirely made of copper, and mount fans of considerable size and power.
Heat sinks tend to get less effective with time due to the build up of dust between their metal fins, which reduces the efficiency with which the heat sink transfers heat to the ambient air. Dust build up can be countered with a gas duster by blowing away the dust along with any other unwanted excess material.
Passive heat sinks are commonly found on older CPUs, parts that do not get very hot (such as the chipset), and low-power computers.
Usually a heatsink is attached to the integrated heat spreader (IHS). It essentially is a large flat plate attached to the CPU (with conduction paste layered between). The plate is used to dissipate or spread the heat locally. Unlike a heatsink, its intent is to redistribute heat and not to remove it. In addition, the IHS offers protection to the fragile CPU.
Passive cooling avoids the generation of fan noise.
没有评论:
发表评论